–{•¶‚ÖƒXƒLƒbƒv

Nagao System INC. is a professional group specializing in physics and chemistry instruments such as original fine pulverization, dispersion and mixing.

TEL. +81-44-954-4486

1-9-30 Katahira Asao-Ward Kawasaki-City Kanagawa-Pref, 215-0023 JAPAN

???????

NAGAO SYSTEM INC. Is a professional group that solves milling, mixing and dispersion, which was considered impossible in the past by high-speed rotation utilization of patented 3D Ball Mill (3D Reactor).

mm or less (Organic / Inorganic) material can be pulverized, mixed and dispersed up to nano, micron (Dry/Wet type) possible.

Furthermore, it is good to mix substances of different gravity and viscosity with unused and evenly mixed (3D Reactor) pellicles and feathers.

Weak points of 2D motion are affected by gravity.
It agglomerates at the bottom with high specific gravity and fine material.
However, high-speed 3D motion makes full use of the inner wall surface of the container.
It is the greatest feature that it does not give agglomeration time even with high specific gravity or fine material.

We manufacture and sell the equipment + special container.

Please feel the difference between the conventional high speed 2D motion (critical) and yunknown areaz high speed 3D motion (Non critical).

The high-speed 3D motion realizing non-criticality enabled non-solidification, high homogeneity mixing, dispersion, milling!

High-speed 3D motion can be expected to further reduce mixing unevenness and further improve milling uniformity.

3D Ball Mill MOVIE(Ver.1)3D Ball Mill MOVIE(Ver.2)3D Ball Mill MOVIE(Ver.3)LEAFLET

Presentation‡@10minPresentation‡A3min Presentation‡B10minPresentation‡C3min Presentation‡D30sec

TOPICS

  • 3D Ball Mill (3D Reactor) is a patented company developed by our company.
    High-speed 3D motion was impossible in the past (2D motion), it enabled highly uniform milling, mixing and dispersing effect, enabling new product development.
    We will propose a new MONOZUKURI(manufacturing) using 3D Ball Mill (3D Reactor).
  • y3D Ball Mill (3D Reactor)z
    E(Organic matterEinorganic matter) and (DryEWet) possible!
    EMilling substances of less than mm units from micrometers to Nano units.
    E Mixing and dispersion of materials with different specific gravities and viscosities can be done uniformly.
    (Reagglomeration prevents nonsolidification.)
    EBecause the whole container surface is used by frictional force, milling heat hardly occurs.
    Therefore, it is possible to milling, mixing and disperse inorganic substances and organic substances.
    EBy adopting a batch system for vessels, it is possible to crush single peaks with high uniformity.
    Noncritical motion by high-speed 3D motion
    EIt is good at milling and mixing which does not destroy the particle shape which made use of frictional force.
  • Superior points of the 3D ball mill(3D Reactor)
    ‡@Dry process pulverization, mixture, dispersion without solidification
    ‡ALow thermogenesis with spherical motion
    ‡BUniform pulverization, mixing and dispersion
    ‡CNon-criticality based on high-speed motion
    ‡DUniform mixing without blade
    ‡EUtilizing friction force and achieved pulverization, mixture, dispersion with maintaining particle form

    yMeritz
    ‡@Thermogenesis problem in 2D motion pulverization, mixture, dispersion
    ySolutionz
    EUtilizing the entire inner area of the container promotes the dispersion of frictional heat and its generation. Effective with organic and inorganic substances.
    ‡AUneven particle size in 2D motion pulverization, mixture, dispersion
    ySolutionz
    EBatched pulverization, mixture, dispersion utilizing friction force of high-speed 3D motion. Rounded particle form and uniform particle size.
    ‡BSolidification in 2D motion dry pulverization, mixture, dispersion
    ySolutionz
    EAchieving no solidification by high-speed 3D motion dry pulverization, mixture, dispersion .
    ‡CUneven 2D motion mixing (because of only one axis)
    ySolutionz
    EWithout blade. High-speed 3D motion makes it possible to use entire inner area of container efficiently. Low thermogenesis and uniform mixing can be achieved.
  • y3D Ball Mill (3D Reactor) Recent Device Usage Examplez
    EMixing and dispersion of 3D printers.
    (Mixing and dispersion of ceramics and resin, etc.)
    EMixing and dispersion of electro conductive paste and ink for electronics.
    (For example, mixing and dispersion having a difference in specific gravity between metal and resin)
    EMixing and dispersion of battery material, phosphor, magnetic material.

    EMixing and dispersion of special ink such as printer.
    (For example, mixing and dispersion of metal or glass and organic solvent)
    EMixing and dispersion of medicines and cosmetics sensitive to thermal change.
    EMultiple special solvent emulsions, mixing and dispersion.
  • yTarget Userz
    ECompanies and universities that make products from materials.
    ECompanies and universities that make high value added products.
    EThings that demonstrate the effect when using fine particles.
    EPerson who is troubled by uniform mixture with small specific gravity and different viscosity.
    EIf you are having trouble with reaggregation (solidification).
    EPeople who need help with milling heat.
  • yAdvantages of Introducing 3D Ball Mill (3D Reactor)z
    EManufacturing loss (Irregular) reduction by improving uniformity.
    EReduction of raw material costs by miniaturization and highly uniform mixing.
    EReduction of manufacturing time and personnel cost.
    EIntroduced manufacturing method which could not be solved by existing equipment.
    (Differentiation from other companies)
  • EJap.Pat. 4974283 Clinostat
    EJap.Pat. 5666220 Three-dimention ball mill
    EJap.Pat. 5620088 Waste decomposition
    EJap.L.O. 2012-176331 Three-demention ball mill and ball mill and milling machines
    EJap.Pat. 5620027 Mixing device rotation
    EUSA.Pat. 6,387,298 B1 Luminescent Materials
    yPCTz
    PCT/JP2016/063183 Mixing method and rotating device
  • Please feel the difference of the unknown area high speed 3D motion from the conventional 2D motion. 3D Reactor MOVIE(Ver.1) 3D Reactor MOVIE(Ver.2) 3D Reactor MOVIE(Ver.5)

(Medium Size) Table top type 2-axis control 3D Ball Mill(3D Reactor) u3D-210-D2v
yPC control version (Manual & Program operation) availablez

šDesign and specifications are subject to change without notice.

(Small Size) 3D Ball Mill(3D Reactor) (Glove box insertion model)u3D-80v
yPC control version (Manual & Program operation) availablez

(Small Size) Separate type 3D Ball Mil(3D Reactor) (Glove box insertion model)u3DB-80v
yPC control version (Manual & Program operation) availablez

yMajor Fields of use products!z

ySuper Pointsz
yTilted Rotation Planetary ball millz
(Patent No.4937502Planetary ball mill)

E (Small Size) Tilted Rotation Planetary Ball Mill uPlanet M2-3Fv
E (Small Size) Tilted Rotation Planetary Ball Mill (Glove box insertion model) uPlanet Min (-F)v

A tilted type planetary ball mill that we developed independently and acquired the patents is a product that other companies can not imitate.
The usual horizontal type planetary ball mill is exercised in only one direction lateral direction of revolution.
Compared to the conventional horizontal type planetary ball mill, our company "tilted type planetary ball mill" can exert crushing effect making full use of impact force several times higher.
The reason for this is strong impulse from two directions, patented 'diagonal in the direction of rotation' and 'sideways in the direction of revolution'.
It is also used as a reactor utilizing kinetic energy, such as mechanical alloying, which makes use of strong impact force, and mechanochemical.
Also, since batch processing is the principle, it is possible to produce high quality products in small quantities.
The field of use of the tilted type planetary ball mill is very diverse.

By using option
ECentrifugal separator
EDispersion mixer

It is possible to use.


yConventional Planetary Ball Millz
EThe rotation axis and the revolution axis are parallel.
ESlowly centrifugal acceleration of horizontal only in the same direction of rotation and revolution.
EThe container receives force at one point of the rotation fixed axis. (The shaft is overloaded.)
EThere is little vertical motion due to horizontal and horizontal 1-axis motion due to rotation and revolution.
ETherefore, the motion of particles is small and the motion of collision is small.

yNagao System INC. tilted type planetary ball mill (Planet series)z
EThe rotation axes of rotation (inclination) and revolution (horizontal) are two directions.
ECentrifugal acceleration occurs about several times as much as the conventional characteristics in the two rotation axes.
EThe container receives force at two points: the revolving fixed axis and the self-contacting rubber. (The shaft is not overloaded.)
ETornado motion occurs by biaxial motion of rotation (inclination) and revolution (horizontal), resulting in high impact force.
ETherefore, the motion of particles is large, strong impact force.

Product Catalog

Nagao System INC. was awarded in January 2018 as "2017 excellent small scale company" from Kanagawa Prefecture.

NAGAO SYSTEM INC. got the J-GoodTech first favorite registration ranking first place.
(February, 2015)

NEWSV’…î•ñ

MAY/16/2018
Nagao System INC. article was published in the Nikkan Kogyo Shimbun.
JUL/18/2018

yTaipei International Plastics & Rubber Industry Show(TAIPEI PLAS 2018)z
Aug.15(Wed.)-Aug.19(Sat.), 2018
09:00 ? 18:00
https://www.taipeiplas.com.tw/
Venue:Taipei Nangang Exhibition Hall 1(TWTC)
http://www.twtcnangang.com.tw/en/visitors
Organizer: Bureau of Foreign Trade
https://www.trade.gov.tw/English/
We will exhibit it at exhibition booth of Sou Le Enterprise Co., Ltd.
http://www.soule.com.tw/
We will exhibit our products at our booth.

JAN/10/2018
Recognize excellent factories & small businesses supporting local economy!
Nagao System INC. received the "Kanagawa prefecture excellent small scale business award" in 2017.
http://www.pref.kanagawa.jp/prs/p1205635.html

Exhibitions Schedule

yTaipei International Plastics & Rubber Industry Show(TAIPEI PLAS 2018)z
Aug.15(Wed.)-Aug.19(Sat.), 2018
09:00 - 18:00
https://www.taipeiplas.com.tw/
Venue:Taipei Nangang Exhibition Hall 1(TWTC)
http://www.twtcnangang.com.tw/en/visitors
Organizer: Bureau of Foreign Trade
https://www.trade.gov.tw/English/
We will exhibit it at exhibition booth of Sou Le Enterprise Co., Ltd.
http://www.soule.com.tw/
We will exhibit our products at our booth.

yTaipei International Mold & Die Industry Fair(TAIMOLD 2018)z
Aug.29(Wed.)-Sep.1(Sat.), 2018
09:00 - 17:00 (Closing one hour early on last day)
https://www.odm-dmi.com/en/
Venue:Taipei Nangang Exhibition Hall 1(TWTC)
http://www.twtcnangang.com.tw/en/visitors
Organizer:CHAN CHAO INTERNATIONAL CO., LTD.
https://www.chanchao.com.tw/en/
We will exhibit it at exhibition booth of Sou Le Enterprise Co., Ltd.
http://www.soule.com.tw/
We will exhibit our products at our booth.

yThe Ceramic Society of Japan The 31st Fall Meetingz
September 5(Wed.)|7(Fri.), 2018
http://www.ceramic.or.jp/ig-syuki/31/index.html
Venue:Nagoya Institute of Technology(Turumai Campus)
https://www.nitech.ac.jp/eng/access/index.html
Organizer:The Ceramic Society of Japan
http://www.ceramic.or.jp/index.html
We will exhibit our products at our booth.
We look forward to your visit.

yCE Taiwan 2018z
September 19(Wed.)-21(Fri.), 2018
https://www.cetaiwan.com.tw/en_US/index.html
Venue:Taipei Nangang Exhibition Hall 1 (TWTC)
http://www.twtcnangang.com.tw/en/visitors
Organaizer: TAITRA
http://www.taitra.org.tw/
We will exhibit it at exhibition booth of Kawasaki city.
We will exhibit our products at our booth.

yAutumn Meeting 2018z
October 30(Tus.)|November 1(Thu.), 2018
http://www.jspm.or.jp/taikaif1.html
Venue:TOKI MESSE Niigata Convention Center
http://www.tokimesse.com/visitor/access/
Organizer:Japan Society of Powder and Powder Metallurgy
http://www.jspm.or.jp/E_index.html
We will exhibit our products at our booth.
We look forward to your visit.

yNew Value Creation Exhibition 2018z
ENovember 14(Wed.) to 16(Fri.), 2018
https://shinkachi-portal.smrj.go.jp/exhibitor/shinkachi2018/
Venue:Tokyo Bigsight East Hall 2E3
http://www.bigsight.jp/english/hotel/transportation/
Organizer:Small & Medium Enterprises and Regional Innovation
http://www.smrj.go.jp/english/index.html
We will exhibit our products at our booth.
We look forward to your visit.

yConstructure Show 2018 in Taipeiz
Nov.16(Fri.)-Nov.19(Mon.), 2018
Venue:Tapei World Trabe Center(TWTC)
http://www.twtc.com.tw/en/e-index.aspx
We will exhibit it at exhibition booth of Sou Le Enterprise Co., Ltd.
http://www.soule.com.tw/
We will exhibit our products at our booth.

yPOWTEX TOKYO 2018z
ENovember 28(Wed.) to 30(Fri.), 2018
http://www.powtex.com/tokyo/en
Venue:Tokyo Bigsight
http://www.bigsight.jp/english/hotel/transportation/
Organizer:uAPPIEvThe Association of Powder Process industry and Engineering, JAPAN
http://appie.or.jp/en/
We will exhibit it at exhibition booth of Kameyama Iron Works.
We will exhibit our products at our booth.

yJapan SMEs Tech & service 2018z
EDecember 11(Tus.) to 13(Thu.), 2018
http://www.shin-monodukuri-shin-service.jp/
Venue:Tokyo Bigsight West1E2 Hall
http://www.bigsight.jp/english/hotel/transportation/
Organizer:National Federation of Small Business AssociationsiN.F.S.B.Aj
https://www.chuokai.or.jp/
We will exhibit our products at our booth.
We look forward to your visit.

y11th Kawasaki International Eco-Tech Fairz
EFeburary 7(Thu.) to 8(Fri.), 2019
https://www.kawasaki-eco-tech.jp/
Venue:Culttz Kawasakihttps://www.kawasaki-eco-tech.jp/access.html
Organizer:Kawasaki International Environment Technology Exhibition Committee
We will exhibit our products at our booth.
We look forward to your visit.

yThe Ceramic Society of Japan The 2019 Annual Meetingz
March 24(SUN.)|26(TUE.), 2019
http://www.ceramic.or.jp/csj/en/meetings.html
Venue:Kougakuin University(Shinjyuku Campus)
https://www.kogakuin.ac.jp/english/about/campus/accessmaps.html#anchor01
Organizer:The Ceramic Society of Japan
http://www.ceramic.or.jp/index.html
We will exhibit our products at our booth.
We look forward to your visit.

ƒiƒrƒQ[ƒVƒ‡ƒ“

ƒoƒi[ƒXƒy[ƒX

NAGAO SYSTEM INC.

1-9-30 Katahira Asao-Ward Kawasaki-City Kanagawa-Pref, 215-0023 JAPAN

TEL +81-44-954-4486
FAX +81-44-954-8258
E-mail fnagao@rose.plala.or.jp